Revetment or blast pen? Telling them apart in VHR imagery

Anyone who's spent time staring at dispersal areas on an airbase tile has hit this fork: is that a revetment or a blast pen? The terms get used loosely in open-source writeups, sometimes interchangeably, which is a problem if you're trying to characterize an airbase's protection posture or compare two sites built to different doctrines. The two structures do different jobs and look different once you know what to check.
What each one is actually for
A revetment is a berm. Earth, sand, sometimes rubble, pushed or stacked into a U-shaped or horseshoe wall around a parking spot. It's unroofed, open to the sky, and its job is to stop blast fragmentation and shrapnel from reaching a neighboring aircraft if one gets hit. You'll see these a lot at older airbases and at sites built under Soviet-influenced doctrine, where dispersal relied on earthworks rather than poured concrete.
A blast pen is the harder cousin. It's typically built from reinforced concrete or prefabricated panels, with two or three walls forming a bay, and sometimes a partial or full roof. When it's fully enclosed it crosses over into hardened aircraft shelter (HAS) territory, which is its own category and usually obvious from the roofline and the blast door. A blast pen without a roof is still a step up from a dirt berm: straighter edges, uniform wall thickness, built to a repeatable design rather than bulldozed by whoever had the equipment that week.
Shape and spacing are the first tell
Revetments tend toward irregularity. Spacing between them varies, the horseshoe openings don't all point the same direction, and the berms themselves often aren't perfectly symmetrical because they were shaped by whatever earthmoving gear was on hand. If you pull up a dispersal area and the individual bays look like they were stamped out with a template, cookie-cutter size, identical spacing, parallel orientation off a taxiway, that's leaning blast pen or hardened shelter, not revetment.
Count them too. A revetment field built for dispersal often has more bays than aircraft, with some left empty or used for decoys. Blast pen rows are usually built closer to the actual aircraft inventory they're meant to shelter, since poured concrete is a bigger capital outlay than pushing dirt.
Shadow and surface texture do the rest
This is the part that actually separates the two on a single still image, no time series needed. An earthen berm has a soft, slightly irregular shadow edge, because the top of the berm isn't a sharp line, it's a mounded slope. The surface on the berm itself often shows texture: scrub growth, erosion rilling, tire tracks from maintenance, sometimes a visibly different soil tone from surrounding ground if it was built from imported fill.
A concrete blast pen wall throws a crisp, straight-edged shadow. The wall top is a hard line, not a slope, so the shadow boundary is clean even at modest resolution. Surface tone on the wall itself tends to be uniform, concrete gray or a painted camouflage pattern, without the texture variation you get on bare earth. If you're working imagery where sun angle gives you decent shadow length, lay a straightedge along the shadow boundary mentally: wavy means earth, straight means built structure.
Watch for the mixed cases
Plenty of airbases run both, often because a site expanded over decades under different doctrines, or a disused earthen field got concrete pens added later at the regime that could afford it. Don't assume a whole dispersal area is one or the other just because the first few bays you check match a pattern. Walk the full apron and revetment line before you characterize the site, because a mixed inventory of pen types is itself a useful fact, it can mark the boundary between an older Soviet-era layout and a newer hardened buildout.
One other wrinkle: construction-stage imagery. A blast pen under construction, before the roof or final wall pour, can look a lot like a revetment for a few weeks, just graded earth and formwork. If you're tracking a site over time, catching that transition is exactly the kind of change a daily pass would flag rather than something you'd need to spot cold on a single frame. Airfield Activity runs that daily comparison against the previous pass and logs runway and shelter construction alongside the aircraft counts, so a pen going from bare earth to poured concrete shows up as a flagged change rather than something you have to notice on your own.
If you're tracking a specific field and want that comparison running in the background, have a look at what Airfield Activity logs day to day.